|
ELECTRO-ACUNPUNCTURE DEVICES |
 |
 |
Pointer Excel II - Hand Held T.E.N.S. and Point Detector with Digital
Display
The Pointer Excel II is a new user-friendly hand-held device with digital
display for location of acupuncture or trigger points. It incorporates an
effective push button stimulation feature for immediate electroacupuncture
treatment of the point or area immediately following its detection.
The digital display helps the user to locate the most accurate acupuncture
or trigger point easily, as the number increases with the lowering of the
electric resistance of the skin (when a maximum number is reached, an
acupuncture point is detected and electroacupuressure may begin).
Self-treatment for electroacupuncture has never been so easy!
This new model has additional features, such as adjustable frequency from 1
- 16 Hz, and polarity reversal switch (for tonification or sedation). It is
one of the most innovative hand-held stimulators available in the market.
Accessories:
- The Pointer Excel II Unit
- Hand electrode for close circuit purposes
- Two probes, diameter 2 mm & 4mm
- Heavy Duty battery
- Instruction Manual
- ABS plastic carrying case
Maintenance:
Maintenance of the Pointer Excel II Stimulator/Detector is limited to
cleaning the stimulator battery contacts and metal electrodes. The
stimulator operates on a 9 volt battery (A 9 volt Duracell or other alkaline
battery is recommended). When adequate stimulation can no longer be
maintained, change the battery. Remove the old battery and replace it with a
new battery. The system will provide stimulation only if the battery is
properly installed.
Basic Principle:
On the body surface, the electric resistance of a trigger point or a
reactive point is lower than in its surrounding areas. It can be readily
located by means of an instrument which is sensitive to resistance changes.
When the metal probe touches a low resistance point the loudspeaker gives a
sound signal. Its pitch rises with the lowering of the electric resistance
of the skin. With this device and method of detection, trigger points thus
located usually produce a strong sensation and reaction to electric
stimulation, and will achieve the best therapeutic results.
Indications and Controls:
Operation of Controls:
1. One sensitivity control knob on the right hand side of the unit to
control the sensitivity (by touching the stimulation probe with the ground
pole) can be read from the Digital Chamber Display. The higher the value,
the higher the sensitivity. During location of trigger or acupuncture
points, the number varies and reach maximum when the exact point is located.
2. An intensity and ON/OFF control knob on the left hand side of the unit to
control the intensity of the output through the metal probe electrode, which
is located at the front tip of the unit.
3. A push type button on the front top of the unit. Press this button to
activate the stimulation mode. A continuous electric pulse of 1 to 16 Hz
(adjustable) is emitted through the metal probe.
4. Frequency adjustment dial, located under the sensitivity control knob, to
adjust the frequency of stimulation from 1 Hz to 16 Hz. The frequency
selected can be read from the display chamber when pressing down the push
type button on the front top of the unit.
5 Polarity change over switch, located at the front side of the unit, to
change the polarity of stimulation from + to – or vise versa.
6. The digital Display chamber is located on the rear top side of the unit.
It features a digital display to show the frequency (from 1 to 16Hz) of
stimulation during operation, and numerical display (maximum around 500 when
sensitivity adjustment to highest range) to show the sensitivity of
detection during the location of acupuncture points.
7. There is a green pilot lamp on top of the unit, next to the push type
button. This will light up when the point location or stimulation mode is in
action.
8. Two ground plates, one located at the front left hand side, and the other
one underneath the unit, allow the user to hold the unit and touch the
ground plate(s) easily in closing the circuit for point detection or
stimulation.
9. There is one jack on the bottom side of the unit. This is for connecting
the hand grounding pole.
| Specifications: |
|
| Output intensity |
0 - 22 mA |
| Micro current output |
0 - 2 microamps |
| Sensitivity adjust control |
0 - 10 |
| Output intensity control |
OFF, 0 - 10 |
| Frequency control |
1 - 16 Hz |
| Polarity reversal switch |
+/- by switch |
| Pulse width |
220 microseconds |
| Pulse shape |
Asymmetric biphasic square wave |
| Push type buttons |
On/STI, Off/LOC |
| Large LCD digital display |
Frequency / sensitivity indicator |
| Indicator lamp |
Pulse rate indicator |
| Power supply |
9V battery |
| Power modes |
Continuous |
| Point detection |
Meter, sound and light indicators |
| Color |
Beige |
| Size |
225mm x 50mm x 38mm |
| Operation temperature |
16°C - 30°C |
| Output channels |
1 |
|
$200 |
|
|
 |
Pointer Plus - Hand Held Acupuncture & Trigger Point Locator / Stimulator
The Pointer Plus is a modern convenient health device, that can give you the
benefits, that are derived from a 4000 year old chinese health science, that
is now being called ELECTRO-ACUPRESSURE. The Pointer Plus Excel is the
latest and most advanced user friendly hand held point locator and
stimulator!
Features a built-in, 0.35" x 1.0" LCD digital display meter for location of
acupuncture and trigger points. Modern, hand held, 6.5" long Pointer Plus
Excel unit offers sensitive acu-point or trigger point location and
stimulation. Location and stimulation are independently adjusted with two
separate control dials for fast and effective relief from aches, pains,
swelling, inflammation, tension, and stress-related symptoms! The portable
battery-operated Pointer Plus is so handy, that you can use it anytime and
anywhere! It's totally non-invasive and painless, because the Pointer Plus
simply tonifies or sedates the affected area!
Electro-acupuncture treatment is painless and effective pain relief is only
3-5 minutes away!
The pulse frequency of the Pointer Plus is fixed at 10 Hz. (recognized in
Japan and Germany as the most useful treatment frequency). The hand held
Pointer Plus offers sensitive acupuncture / trigger point location and
tonification or sedation. A flashing light and sound indicate when point
detection is made; the spring activated detection allows a uniform pressure
when searching while the grounding circuit is made by holding the metal
plate on the side of the unit or with the hand grounding pole.
Accessories:
- Pointer Plus Unit
- Hand grounding pole
- Two probes, diameter 2 mm & 4mm
- Heavy Duty battery
- Instruction Manual
- ABS plastic carrying case
Maintenance:
Maintenance of the Pointer Excel II Stimulator/Detector is limited to
cleaning the stimulator battery contacts and metal electrodes. The
stimulator operates on a 9 volt battery (A 9 volt Duracell or other alkaline
battery is recommended). When adequate stimulation can no longer be
maintained, change the battery. Remove the old battery and replace it with a
new battery. The system will provide stimulation only if the battery is
properly installed.
Basic Principle:
On the body surface, the electric resistance of a trigger point or a
reactive point is lower than in its surrounding areas. It can be readily
located by means of an instrument which is sensitive to resistance changes.
When the metal probe touches a low resistance point the loudspeaker gives a
sound signal. Its pitch rises with the lowering of the electric resistance
of the skin. With this device and method of detection, trigger points thus
located usually produce a strong sensation and reaction to electric
stimulation, and will achieve the best therapeutic results.
Indications and Controls:
Features:
1. Modern Spring Type Probe Tip
The interchangeable spring type probe provides a constant pressure to the
area or points, thus providing better accuracy during point location
searching. It is important to note that any part of the body may be induced
to produce a point location signal depending on the amount of pressure used
during location. Thus it is important when locating the trigger or
acupuncture pointers to use the lightest and least amount of pressure
possible on the surface of the skin. Also, the movement of the probe when
searching for the point should be smooth and graceful, always maintaining
the same light uniform constant pressure until the correct point is found.
The unique spring mechanism of the Pointer Plus probe will add in correcting
for any slight variations in the applied pressure.
2. Interchangeable Probes
Two different probes are provided for different applications. The larger
probe may be used for larger areas or body points while the small probe may
be used for ear points or other smaller body points.
3. Sensitivity Adjustment
The point detection sensitivity is adjustable. The “SEN” knob is used to
either increase (clockwise adjustment) or decrease (counter-clockwise)
sensitivity when use on different skin conditions.
4. Hand Grounding Pole Accessory
The patient must hold the hand grounding pole in order to create a complete
electrical circuit. This accessory is easily attached or removed from the
unit. (Note: this unit may also be sued without the grounding pole, however,
in this case the practitioner must contact both the grounding plate on the
unit as well as hold the bare skin of the patient with his hand to complete
the circuit.) The grounding pole is not necessary when using on oneself
providing the grounding plate on the unit is contacted.
5. Immediate Point location and Treatment
The button on top of the unit may be pressed to activate the stimulation
mode. A continuous electric pulse of 8 to 10 Hz is emitted through the
probe, the intensity may also be adjusted from 0 to 22 mA. The intensity is
controlled with the intensity knob labeled “INT”
Note: The Stimulation for the Pointer Plus may be increased by lightly
moistening the skin.
Directions:
1. Insert the 9 volt battery onto the battery clips, the positive and
negative poles of the battery should always be matched correctly with the
respective battery clips. A 9 volt Duracel or other alkaline battery is
recommended for the best performance.
2. Select the correct probe for use with ear or body points
The larger probe may be used for larger areas or body points. The small
probe may be used for ear points or other smaller body points
3. For self use, touch the grounding metal plate on the front side of the
unit and then search for the point.
4. Press each point slightly, the probe uses a spring mechanism so that a
constant pressure may be maintained during location. The respective trigger
or acupuncture point is located when a continuous sound is heard from the
buzzer and at the same time the LED light located in front of the APD / STI
button is flashing continuously.
5. The sound emitted from the buzzer may be muffled or reduced by covering
the holes of the metal grounding plate with your thumb.
6. If stimulation is required on this point, simply adjust the intensity
knob “INT” to an acceptable level and press the
APD /STI button. When this button is released, the unit is immediately
returned to the point detection mode. Pressing the APD / STI button again
will produce output stimulation.
7. It is recommended to begin treatment with a low intensity setting,
thereafter turning the “INT” control until a comfortable intensity is
reached.
8. In order to treat patients, the grounding pole must be attached with the
plug jack to the bottom of the unit. The patient must hold the grounding
pole to complete the electrical circuit which then activates both the
detection and stimulation functions. The above procedures 6 to 13 are then
followed.
9. Turn off the unit after use. Remove the battery from the unit when the
device will not be used for a long period.
| Specifications: |
|
| Output intensity |
0 - 22 mA |
| Frequency of output |
10 Hz |
| Output intensity control |
OFF, 0 - 10 |
| Pulse width |
240 microseconds |
| Pulse shape |
Biphasic square wave with
negative spike |
| Push type buttons |
On/STI, Off/APD |
| Indicator lamp |
Pulse rate indicator |
| Power supply |
9V battery |
| Power modes |
Continuous |
| Point detection |
Sound and light indicators |
| Color |
Beige |
| Size |
170mm x 33mm x 33mm |
| Operation temperature |
16°C - 30°C |
| Output channels |
1 |
|
$150 |
|
|
|
